#
# Shorewall -- /etc/shorewall/tcpri
#
# For information about entries in this file, type "man shorewall-tcpri"
#
# See http://shorewall.net/simple_traffic_shaping.htm for additional
# information.
#
###############################################################################
# 
# This file is used to specify the priority of traffic for simple traffic shaping
# (TC_ENABLED=Simple in shorewall.conf(5)). The priority band of each packet is
# determined by the last entry that the packet matches. If a packet doesn't match
# any entry in this file, then its priority will be determined by its TOS field.
# The default mapping is as follows but can be changed by setting the TC_PRIOMAP
# option in shorewall.conf(5).
# 
# TOS     Bits  Means                    Linux Priority    BAND
# ------------------------------------------------------------
# 0x0     0     Normal Service           0 Best Effort     2
# 0x2     1     Minimize Monetary Cost   1 Filler          3
# 0x4     2     Maximize Reliability     0 Best Effort     2
# 0x6     3     mmc+mr                   0 Best Effort     2
# 0x8     4     Maximize Throughput      2 Bulk            3
# 0xa     5     mmc+mt                   2 Bulk            3
# 0xc     6     mr+mt                    2 Bulk            3
# 0xe     7     mmc+mr+mt                2 Bulk            3
# 0x10    8     Minimize Delay           6 Interactive     1
# 0x12    9     mmc+md                   6 Interactive     1
# 0x14    10    mr+md                    6 Interactive     1
# 0x16    11    mmc+mr+md                6 Interactive     1
# 0x18    12    mt+md                    4 Int. Bulk       2
# 0x1a    13    mmc+mt+md                4 Int. Bulk       2
# 0x1c    14    mr+mt+md                 4 Int. Bulk       2
# 0x1e    15    mmc+mr+mt+md             4 Int. Bulk       2
# 
# The columns in the file are as follows.
# 
# BAND - {1|2|3}
# 
#     Classifies matching traffic as High Priority (1), Medium Priority (2) or
#     Low Priority (3). For those interfaces listed in shorewall-tcinterfaces(5),
#     Priority 2 traffic will be deferred so long and there is Priority 1 traffic
#     queued and Priority 3 traffic will be deferred so long as there is Priority
#     1 or Priority 2 traffic to send.
# 
# PROTO - protocol[,...]
# 
#     Optional. The name or number of an IPv4 protocol.
# 
#     Beginning with Shorewall 4.5.12, this column can accept a comma-separated
#     list of protocols.
# 
# PORT(S) - port [,...]
# 
#     Optional. May only be given if the the PROTO is TCP (6), UDP (17), DCCP
#     (33), SCTP (132) or UDPLITE (136). A list of one or more port numbers or
#     service names from /etc/services. Port ranges of the form lowport:highport
#     may also be included.
# 
# ADDRESS - [address]
# 
#     Optional. The IP or MAC address that the traffic originated from. MAC
#     addresses must be given in Shorewall format. If this column contains an
#     address, then the PROTO, PORT(S) and INTERFACE column must be empty ("-").
# 
# INTERFACE - [interface]
# 
#     Optional. The logical name of an interface that traffic arrives from. If
#     given, the PROTO, PORT(S) and ADDRESS columns must be empty ("-").
# 
#     Note
# 
#     INTERFACE classification of packets occurs before classification by PROTO/
#     PORT(S)/ADDRESS. So it is highly recommended to place entries that specify
#     INTERFACE at the top of the file so that the rule about last entry matches
#     is preserved.
# 
# HELPER - [helper]
# 
#     Optional. Names a Netfilter protocol helper module such as ftp, sip,
#     amanda, etc. A packet will match if it was accepted by the named helper
#     module. You can also append "-" and a port number to the helper module name
#     (e.g., ftp-21) to specify the port number that the original connection was
#     made on.
# 
###############################################################################
#BAND	PROTO	PORT		ADDRESS		INTERFACE	HELPER